You searched for all products
|
|
|
|
|
AB702c: Carbon Fiber Aero-Bubble 12 high x 62 x23 wide.
|
|
|
|
|
|
|
BL141: Same as BL140 but bottom flange is flat to fit a flat surface bumper.
Fits 6" I.D. hose. Inlet opening 14-1/2 x 7.
Overall length is 9".
(Extension also necks down to 5" I.D.)
6" neck is 6-7" from opening. 5" Neck is 8-9" from front opening.
|
|
|
|
|
|
|
BL140: Bottom flange has slight curve to fit a bumper that has a slight "roll-under". Fits 6" I.D. hose. Inlet opening 14-1/2 x 7".
Overall length is 9" (Extension also necks down to 5" I.D.)
6" neck is 6-7 inches from opening. 5" Neck is 8-9".
|
|
|
|
|
|
|
Carbon Fiber Front wrap around front end, less hood, with CH-281cbumper built in and front spoiler / chin spoiler built in
This is a race item, Has full flanges for dzus to hold hood to fenders. Front grill blanked off, headlites blanked off.
|
|
|
|
|
|
|
|
PR702c: Carbon Fiber with Black Gel Coat. This scoop was designed to be cut down or left full size to fit your turbos, throttle body or nitrous set-ups under the hood.
|
|
|
|
|
|
|
PR702cc: Carbon Fiber with CLEAR Gel Coat for Carbon Fiber look. This scoop was designed to be cut down or left full size to fit your turbos, throttle body or nitrous set-ups under the hood.
|
|
|
|
|
|
|
S1737: High Back Seat, Carbon Fiber
17 Wide x 37" High
Cut outs for seat belts, molded front edge to fit over frame rail and rubber edge trim. 7 lbs.
|
|
|
|
|
|
|
S1837: Carbon Fiber High Back Seat - Wide
18 Wide x 37" High
Cut outs for seat belts, molded front edge to fit over frame rail and rubber edge trim. 7 lbs.
|
|
|
|
|
|
|
|
S-2037: High Back Seat, Carbon Fiber
20- 1/2 Wide x 37" High
Cut outs for seat belts, molded front edge to fit over frame rail and rubber edge trim. 7 lbs.
|
|
|
|
|
|
|
S1727: Carbon Fiber Low Back Seat
17" Wide x 27" High
Cut outs for seat belts, molded front edge to fit over frame rail and rubber edge trim. 4-1/2 lbs.
|
|
|
|
|
|
|
4822: 48" x 96" sheet (4x8) 1 mm thick (.040)
Slightly denser and stronger than our "general purpose".
Clear Coat one-side.
|
|
|
|
|
|
|
|
4832: 48" x 96" sheet (4X8) .200" thick. Composite style. Clear Coat both sides.
|
|
|
|
|
|
|
|
4812: 48" x 96" sheet (4x8) 1 mm thick (.043-050"). Composite style. Clear Coat one-side.
|
|
|
|
|
|
|
|
4803: 48" x 96" sheet (4x8) 1 mm thick (.040)
Slightly denser and stronger than our "general purpose".
Clear Coat one-side.
|
|
|
|
|
|
|
Wheel Tub Extender, 3 lbs
17" Wide x 27" High
|
|
|
|
|
|
|
|
SP174C: CENTER SECTION ONLY OF (SP-174) 74-81 CAMARO REAR DECK
|
|
|
|
|
|
|
PR2: Outside mounting flange.
This replica is the rare Challenger T/A hood scoop. Full open interior allows maximum clearance for your carburetion. Exterior flange permits user to fasten to hood by using rivets or sheet metal screws.
|
|
|
|
|
|
|
PR23: Same as PR2, but has INSIDE mounting flange.
This replica is the rare Challenger T/A hood scoop. Full open interior allows maximum clearance for your carburetion. Rear section (20" long) allows 21-1/2" width clearance underneath.
|
|
|
|
|
|
|
C133: CHROME INSERT FILLER PANEL for C-130 R.S. nose (NOT CHROME, this is a fiberglass replica).
|
|
|
|
|
|
|
SC105: Replica of 69-70 Cobra Jet Mach-1 Mustang. It eliminates the turn signal lights which are mounted in the rear of the scoop. Full outside flange aids in riveting or bolting to your hood. This scoop can also be molded in for that finished look.
|
|