You searched for all products
|
|
|
|
|
PR702cc: Carbon Fiber with CLEAR Gel Coat for Carbon Fiber look. This scoop was designed to be cut down or left full size to fit your turbos, throttle body or nitrous set-ups under the hood.
|
|
|
|
|
|
|
S1737: High Back Seat, Carbon Fiber
17 Wide x 37" High
Cut outs for seat belts, molded front edge to fit over frame rail and rubber edge trim. 7 lbs.
|
|
|
|
|
|
|
S1837: Carbon Fiber High Back Seat - Wide
18 Wide x 37" High
Cut outs for seat belts, molded front edge to fit over frame rail and rubber edge trim. 7 lbs.
|
|
|
|
|
|
|
|
S-2037: High Back Seat, Carbon Fiber
20- 1/2 Wide x 37" High
Cut outs for seat belts, molded front edge to fit over frame rail and rubber edge trim. 7 lbs.
|
|
|
|
|
|
|
S1727: Carbon Fiber Low Back Seat
17" Wide x 27" High
Cut outs for seat belts, molded front edge to fit over frame rail and rubber edge trim. 4-1/2 lbs.
|
|
|
|
|
|
|
4822: 48" x 96" sheet (4x8) 1 mm thick (.040)
Slightly denser and stronger than our "general purpose".
Clear Coat one-side.
|
|
|
|
|
|
|
|
4832: 48" x 96" sheet (4X8) .200" thick. Composite style. Clear Coat both sides.
|
|
|
|
|
|
|
|
4812: 48" x 96" sheet (4x8) 1 mm thick (.043-050"). Composite style. Clear Coat one-side.
|
|
|
|
|
|
|
|
4803: 48" x 96" sheet (4x8) 1 mm thick (.040)
Slightly denser and stronger than our "general purpose".
Clear Coat one-side.
|
|
|
|
|
|
|
Wheel Tub Extender, 3 lbs
17" Wide x 27" High
|
|
|
|
|
|
|
SP174C: CENTER SECTION ONLY OF (SP-174) 74-81 CAMARO REAR DECK
|
|
|
|
|
|
|
PR2: Outside mounting flange.
This replica is the rare Challenger T/A hood scoop. Full open interior allows maximum clearance for your carburetion. Exterior flange permits user to fasten to hood by using rivets or sheet metal screws.
|
|
|
|
|
|
|
PR23: Same as PR2, but has INSIDE mounting flange.
This replica is the rare Challenger T/A hood scoop. Full open interior allows maximum clearance for your carburetion. Rear section (20" long) allows 21-1/2" width clearance underneath.
|
|
|
|
|
|
|
C133: CHROME INSERT FILLER PANEL for C-130 R.S. nose (NOT CHROME, this is a fiberglass replica).
|
|
|
|
|
|
|
SC105: Replica of 69-70 Cobra Jet Mach-1 Mustang. It eliminates the turn signal lights which are mounted in the rear of the scoop. Full outside flange aids in riveting or bolting to your hood. This scoop can also be molded in for that finished look.
|
|
|
|
|
|
|
|
Cowl induction hood 3-1/2 tall 71-72 Cutlass
|
|
|
|
|
|
|
SC116: Fully bolt on cowl induction scoop. Internal 2" wide flange for easy mounting. Will cover up hole in your hood that was cut to accommodate the #SC284 aero-scoop (SC284 also mounts with internal flange). Mounting bolts are supplied with this scoop.
|
|
|
|
|
|
|
SC108: Our most popular scoop, this replica of the notorious Z28 Camaro cowl induction, features a full 2 1/4 inch height. Designed to be riveted or screwed on to an original steel hood, it can also be glassed and molded into any of our fiberglass hoods.
|
|
|
|
|
|
|
SC109: This scoop features the same fine qualities as the SC108, but is an additional 6 inches longer. It is most commonly attached to larger hoods like 68 Fire-bird or 70-81 Trans-Am.
|
|
|
|
|
|
|
SC328: Scoop is designed to fit 87-92 Mustang hood. Height is 2 1/4. Overall length is 47". Overall width is 31" at the back (including outside mounting flange). Flange size is 1-1/4", leaving actual scoop width of 28". Scoop tapers toward the front.
|
|